Folding Tripod Camp Stool

tripod_title
You’ll need some tools:
  • Sander
  • Center-finder (optional, but helps)
  • Drill
  • Screwdriver
  • Small socket wrench to fit acorn nuts
  • Rags
  • Knife
You’ll need a few materials:
  • Three 1 1/8” Birch hardwood dowels - enough for three 24” pieces
  • One steel 2.75” bolt - UPDATED, the brass is too soft for structural stress
  • One 1.5” eyehole bolt
  • Two brass acorn nuts
  • Three brass washers
  • Three brass finishing washers
  • Three brass 1” wood screws (big enough not to slip through the finishing washer)
  • Finish - I used Osmo PolyX-Oil
  • Leather or other heavy material for seat

In honor of this month’s Design*Sponge theme of the outdoors, how about we build an old-fashioned camping stool? First of all, have you seen modern folding tripod stools? They are ugly as sin and your grandpa would be ASHAMED if you bought one. With the help of some hefty dowels, a little hardware and a piece of leather or heavy canvas – you’ll be sitting by the campfire in style. Also, the materials will only set you back about $25.

In addition, I’ve got to give proper respect to the super creative Kate Pruitt at Design*Sponge for sparking this idea… It’s great to work with her and the D*S crew.

Instructions:

1. Start by cutting your dowels to 24” or closest to that. I bought two 48” dowels, so each leg is about 23 7/8 after the saw blade’s share. Drill a hole completely through each one, 10.5” from the top of each leg. Find the center of each leg’s top, and drill a small pilot hole for your seat mounting screws. You’ll need this pilot hole to prevent your legs from splitting. Sand each of the legs smooth, and a little around the edge of the tops, and a good amount on each bottom to round it out more. It doesn’t have to be perfect, just make sure you don’t shorten any leg with too much rounding.

2. After the legs are cut, drilled and sanded, apply your choice of finish and set aside to dry. As they are drying, you can work on the seat material. I’m including a downloadable template for you to create your seat with. I chose leather because I have plenty of it around, but you could sew up a heavy canvas seat or any number of materials. Make sure it’s heavy and sufficiently reinforced since there will be a good amount of stress on each corner.

On one corner of the seat, I left a tab for the carry strap, but this is optional. Mine’s attached to a closure strap, which I recommend having regardless of a carry strap. It’ll keep your stool from popping open in storage or carrying. I edged my leather pieces and treated the smooth surfaces with carnauba wax.

3. Once the legs are dry, assemble the structure assembly by threading two of the legs together with the bolt, with the eyehole bolt in the middle. Use washers on both ends, and attach the acorn nut. I actually cut my bolt down a little bit with a hacksaw, so it fit close. You’ll need a little play in the assembly to move, but it shouldn’t be gaping. Once those two legs are secure, feed the eyehole bolt (which I cut down a little too) into the third leg and attach with a washer and acorn nut. Tighten both acorns securely with a socket wrench.

4. After the base is complete, attach your seat to each leg using a large finishing washer and the wood screw. Don’t over-tighten and strip out your holes, for you’ll need all the strength on these mounting points. After everything is secure, you can take a seat. The main bolt might bend a little to the stress, but that’s fine, it keep its bend permanently and that shape will aid in the folding-up state. Now you’re ready for your next campfire sitting in distinguished comfort.

filed as: , , , , , , , , , , ,   ||   79 Comments

Maple Salt Cellar

maple_title

After my first attempt at making a salt cellar / vessel for Design*Sponge, I figured I wanted to try some more styles. The first one was going to be a gift for my Mom, but after finishing it, I realized it was too modern for her home aesthetic. So, I gave her the walnut one as a ‘placeholder’ gift and said I’d be making her one that better suited her place. I ventured out to the amazing Goby Walnut in search of some boards, and came across a couple maple boards that I couldn’t live without.

Working with maple, I found it to be a little more tricky than walnut. Both are hardwoods, but maple seems REALLY hard. And with the figure in the grain, it was even more challenging. Sanding went well, but turning the cellar on the lathe was interesting. True, you’re not supposed to be really turning wood in that direction of the grain, and it definitely left some tear-out… but I just kept sanding and sanding. Eventually I removed most of the tear-out and got the wood to a smooth point.

After forming, I used OSMO again and I love that stuff more each time. This time I used matte clear Polyx-Oil. If you want to review the instructions, you can check out my walnut cellar post.

filed as: , , , , , , , , ,   ||   12 Comments